back          
         
       
         
             
 

Complete kits

  
 
Kit Partno. Foto Description
Alfa V6 12V - SF45 CKAL01 6 Single Bore Bodies SF45/0/1 with OWK kit (operating wheel linkage), 6 inlet manifolds, 2 fuelrails and 6 airhorns 45x90mm
Alfa V6 24V - SF45 CKAL02 6 Single Bore Bodies SF45/0/1 with OWK kit (operating wheel linkage), 6 inlet manifolds, 2 fuelrails and 6 airhorns 45x90mm
BMW Mini - SF40 CKB01

4 Single Bore Bodies SF40/0/1, 1 inlet manifolds, 1 fuelrail and 4 airhorns 40x40mm.

This kit is for the early square ported engine.
Chrevrolet LS1/2/6 - SFD52 CKCT01 8 Single Bore Bodies SFD52/0/1 with OWK kit (operating wheel linkage), 2 inlet manifolds, 2 fuelrails and 8 60mm long  60mm
Chevrolet LS7 - SFD52 CKCT02 8 Single Bore Bodies SFD52/0/1 with OWK kit (operating wheel linkage), 2 inlet manifolds, 2 fuelrails en 8 60mm long airhorns
Chevrolet LS3 - SFD52 CKCT03 8 Single Bore Bodies SFD52/0/1 with OWK kit (operating wheel linkage), 2 inlet manifolds, 2 fuelrails en 8 20mm long airhorns
Chevrolet LS3 - SFD taper CKCT03C 8 tapered Single Bore Bodies SFD58//45/0 with OWK kit (operating wheel linkage), 2 inlet manifolds, 2 fuelrails, 8 20mm long airhorns, 2 carbon airboxes, throttle position sensor, coil pack mounting brackets and new breathers
Ford Duratec - TBP45 CKFD07

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 90mm long airhorns
Ford Duratec 2.0L - SF taper CKFD10

4 tapered Single Bore Bodies SF51/4.5/1,

1 inlet manifold, 1 fuelrail and 4 83mm long airhorns
Ford V6 Duratec - SF45 CKFD12

6 Single Bore Bodies SF45/0/1 with OWK kit (operating wheel linkage), 6 inlet manifolds, 2 fuelrails and 6 airhorns 45x90mm.

 

The kit is for the 3.0L Mondeo engine.
Ford Cosworth YB - SF taper CKFD01N

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns 48x90mm
Ford Zetec - SF taper CKFD02N

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns 48x90mm

 

The kit is for the 1.8L and 2.0L engine.
Ford Zetec - TB45 CKFD03

1 set Twin Bore Bodies TBP45i, 1 inlet manifold,

1 fuelrail and 4 airhorns 45x90mm

Ford BDA - SF taper CKFD11

4 tapered Single Bore Bodies SF51/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns
Ford Scorpio V6 - SF45 CKFD06

6 Single Bore Bodies SF45/0/1 with OWK kit (operating wheel linkage), 1 inlet manifold, 2 fuelrails and 6 airhorns 45x40mm.

 

The kit is for the V6 BOA engine.
Ford Cyclone 3.5L - SF45 CKFD14 6 Single Bore Bodies SF45/0/1 with OWK kit (operating wheel linkage), 6 inlet manifolds (cross-over),  2 fuelrails and 6 curved airhorns
Honda B16 & 18 C5 - SF taper CKHA01

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns 48x90mm
Honda B18 C1 & C4 - SF taper CKHA02

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns 48x90mm
Honda B16 & B18 C5 - TBP45 CKHA03

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 airhorns 45x90mm

Honda S2000 - SF taper CKHA05

4 tapered Single Bore Bodies SF51/4.5/1,

1 inlet manifold, 1 fuelrail and 4 83mm long airhorns
Honda K20 EP3 - SF taper CKHA07

4 tapered Single Bore Bodies SF51/4.5/1, 1 inlet manifold,

1 fuelrail and 4 83mm long airhorns. Modification of the water pump housing is required and the standard Honda injectors will need replacing with Bosch or Pico style.
Honda K20 FD2 - SF taper CKHA08

4 tapered Single Bore Bodies SF51/4.5/1, 1 inlet manifold,

1 fuelrail and 4 83mm long airhorns. Modification of the water pump housing is required and the standard Honda injectors will need replacing with Bosch or Pico style.
Hyundai Lantra - SF taper CKHI01

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns 48x90mm
Jaguar V6 - SF45 CKJR02 6 x Single Bore Bodies 45/0/1 with OWK kit (operating wheel linkage), 2 inlet manifolds, 2 fuelrails and 6 airhorns 45x90mm.

The kit is for the 3.0L engine.
Mitsubishi Turbo 70mm CKMM01

70mm Turbo Plenum, 1 inlet manifold, 1 fuelrail, 4 19mm long airhorns, 1 Single Bore Body SFGT70, special throttle pot adapter and idle adapter to fit the standard Evo 8 parts.

 

The kit is for the 4G63 Evo 4-8 engine.
Mazda MX5 1.8L NB - TB45 CKMZ01

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 airhorns 45x40mm .

 

The kit is for the MX5 and MK2 1.8L NB engine.
Mazda MX5 1.8L NA - TB45 CKMZ02

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 airhorns 45x40mm .

 

The kit is for the MX5 and MK2 1.8L NA engine.
Mazda MX 1.6L - TB42 CKMZ03

1 set Twin Bore Bodies TBP42i, 1 inlet manifold, 1 fuelrail and

4 airhorns van 42x40mm .

 

The kit is for the MK1 and MK2 1.6L engine.
Mazda MX 2.0L NC - TB45 CKMZ04

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 airhorns van 45x40mm .
Nissan SR20 - SF taper CKNN01

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns 48x90mm
Nissan VQ 3.5L - SF taper CKNN02

6 tapered Single Bore Bodies SF51/4.5/1 with OWK kit (operating wheel linkage), 2 inlet manifolds, 2 fuelrails and

6 airhorns 51x83mm
Nissan VQ 3.5L - SF taper with curved air horns CKNN02C

6 tapered Single Bore Bodies SF51/4.5/1 with OWK kit (operating wheel linkage), 2 inlet manifolds, 2 fuelrails and

6 curved airhorns
Opel  2L XE - SF taper CKVX07

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifold, 1 fuelrail and 4 airhorns 48x90mm

 
Opel 2L XE 27° - TB45 CKVX03

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 airhorns 45x90mm.

 

The kit is for a front engine rear wheel drive car where the engine is upright and the throttle bodies are horizontal.
Opel 2L XE 34° - TB45 CKVX04

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 airhorns 45x90mm.

 

The kit is for a front engine front wheel drive car where the engine is tilted back 7 degrees and the TB's are horizontal.

Opel 2L XE 0° - TB45 CKVX05

1 set Twin Bore Bodies TBP45i, 1 inlet manifold, 1 fuelrail and

4 airhorns 45x90mm
Opel V6 - SFS42 CKVX06 6 short Single Bore Bodies SFS42/0/1 with OWK kit (operating wheel linkage), 6 inlet manifolds, 2 fuelrails and 6 curved airhorns
Porsche 3 stud - SF CKPEO1

6 Single Bore Bodies SF45/0/1 with a special linkage, 6 inlet manifolds which can be bored to the size of your inlet port, 2 fuelrails and 6 airhorns 45x90mm.

 

This kit is for the 3.6 and 3.8 litre 964 engines.

See also kit CLPEO3.
Porsche 2 bolt large port - SF taper CKPEO2 6 tapered Single Bore Bodies SF48/4.5/1 with a special linkage, 2 inlet manifolds, 2 fuelrails and 6 airhorns 48x90mm.

The kit is for the 3.2L Carerra engine.
Porsche 3 stud - SF taper CLPEO3

6 tapered Single Bore Bodies SF51/4.5/1 with a special linkage, 6 inlet manifolds which can be bored to the size of your inlet port, 2 fuelrails and 6 airhorns 51x83mm.

 

The kit is for the 3.6L and 3.8L 964 engines.

See also kit CKPEO1.
Porsche watercooled - SF taper CKPEO4 6 tapered Single Bore Bodies SF48/4.5/1 with s special linkage, 2 inlet manifolds, 2 fuelrails and 6 airhorns 48x90mm.

The kit is for the watercooled 911 engine.
Porsche 2 bolt small port - SF40 CKPEO5 6 Single Bore Bodies SF40/0/1 with a special linkage, 2 inlet manifolds, 2 fuelrails and 6 90mm long airhorns.

The kit is for the 2.0L and 3.0L 911 engine.
Porsche GT3 - SF taper CKPE06

6 tapered Single Bore Bodies SF51/4.5/1 with a special linkage, 2 inlet manifolds which can be bored to the size of your inlet port, 2 fuelrails and 6 airhorns 51x83mm.

 

The kit is for the 911 GT3 engine.
Proton / Mitsubishi 4G93 - SF CKPR01

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifolds, 1 fuelrail and 4 airhorns 48x90mm
Peugeot / Cìtroën TU5 - ST taper CKPG01

4 tapered Single Bore Bodies SF45/4.5/1,

1 inlet manifolds, 1 fuelrail and 4 airhorns 45x90mm.

 

The kit is for the Saxo and 106Gti engine.
Peugeot / Cìtroën 2.0L - SF taper CKPG02

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifolds, 1 fuelrail and 4 airhorns 48x90mm.

 

The kit is for the 206Gti engine.
Peugeot Mi16 - TB45 CKPG03 1 set Twin Bore Bodies TBP45i, 1 inlet manifolds, 1 fuelrail and 4 airhorns 45x90mm.

The kit is for the Mi16 and Citroën BX engine.
Cìtroën C2 - ST taper CKPG04

4 tapered Single Bore Bodies SF45/4.5/1,

1 inlet manifolds, 1 fuelrail and 4 airhorns 45x90mm.

 

The kit is for the Citroën C2 engine.

 
Renault Megane - SF taper CKRT02

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifolds, 1 fuelrail and 4 airhorns 48x90mm.

 

The kit is for the 2.0L 16V engine.

 
Renault Clio 172 - SF taper CKRT03

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifolds, 1 fuelrail and 4 airhorns 48x90mm.

 

Teh kit is for the Clio 172, 182, Cup and RS engine. 
Rover K - SF taper CKRV01N

4 tapered Single Bore Bodies SF48/4.5/1,

1 inlet manifolds, 1 fuelrail and 4 airhorns 48x90mm.

 

Teh kit is for the 1.6L, 1.8L and 2.0L engine. 
Suzuki Hyabusa - SS42 CKSI01 4 Single Bore Bodies (Spigot) SS42/0/1, 1 inlet manifolds and 4 carbon airhorns 2x50mm